Friday, December 3, 2010

Installing Mobo, CPU and memory

1. Before you start ...

The first thing that comes first, make sure you have everything you need to get started. What's good just to go to work does not have everything you need? This can be a bit 'of time, but it's definitely worth it. Once you have all the inventory, it's time to start! In addition to all of your parts, you have a large workspace and two or three hours to focus on the task at hand. Make sure to remember that the carpet and / orstatic is your worst enemy. Static electricity can fry components, and sometimes void any warranty you may have (especially with the control and guarantees ... sometimes you just have bad components). A useful accessory to have with you is a wrist strap - are very cheap and can often be found in your local computer parts store for six dollars or less. A floor carpet is your best place to build. Get your screwdriver, anti-static strap (belt) andDownload the latest drivers part of the web sites of the sellers' and burn to CD - often the drivers supplied with the product will be different versions of data - this can help reduce stress later.

2. Installing the motherboard (motherboard)

Now we can start with the good things: the installation of the motherboard. Remove the motherboard from its antistatic package and place on top of the same pocket. Take care to avoid any potential power "fatal" static.Install the CPU, the heatsink and memory modules. Do this before you screw the motherboard. Since each motherboard is different, you must check the manual as guide you through the installation process. First, lift the lever on the CPU socket, so you can install the CPU. Carefully line up the pins and insert the chip into the socket, not by force, does not fit, unless it is properly oriented. An arrow or a missing pin on one corner of theThe chip will show you how to align things. Release the lever and put the CPU in place.

Then, follow the manufacturer's instructions to install the CPU heatsink and fan that the shows. If you purchased an OEM CPU and a heat sink aside, you can have) a thin layer of thermal compound that came with the heatsink on the chip to ensure good heat transfer (some come with thermal paste already applied.Applying the clip that keeps the power instead of heat sink may require a fair amount. Plug the fan power connector into the motherboard.

Note: Choose the processor first: With the release of new Intel Conroe processors from Intel, AMD has passed as a leader in graphics processing. Not only that, but he also managed to increase energy efficiency. Check the latest reviews ... find this is not hype. Make sure you have more time toChoose the correct processor - is surely the most important decision you will make.

Note: Choose the motherboard after selecting the processor: make sure that when you select the CPU, the CPU is compatible with your motherboard. This is indicated by "taking" of the process - check the detailed specifications and you'll find what your motherboard supports processors. Some only support AMD, Intel and others only certain types of support in every waySure.

Often you can both your process and get your motherboard included - which means that the dealer has the time to ensure that both the motherboard and processor are compatible adopted - is also a way to save a few dollars - not to save time as the installation. Socket A, Socket 939 and Socket 940 are designed to work with Athlon processors, while Socket 478 and the new socket LGA 775 for Intel CPUs. The system chip set (the chips that pass data between devicesand the CPU) is the other component that differs among motherboards, which determines which integrated components (graphics, audio, Ethernet, etc.) will be included. I do not count on using the integrated chipset to run the games, but are fine with the small stuff.

Related : AutoCAD LT 2010 Store. LOWER Prices in Same Item

Thursday, December 2, 2010

As the temperature of the CPU Monitor Software helps your computer

It 'also important for processors and a number of different pieces of hardware that could report the temperature of your computer monitor. This is to prevent damage that may occur due to overheating of the system. To ensure that the CPU is not overheating, you may want to look at the software options that allow you to alert you to high temperatures and that could affect the computer.

It 's very important to look at thiscomponents to ensure that your computer does not fail and cause problems with the hardware that could take place due to overheating. Of course, there are many different hardware options, such as cooling fans and some heat sinks that help distribute heat around the CPU. Well, it's very hard to keep your computer cool all the time, especially if the parties simply great amounts of some of the high temperatures during the use of issue. Components such as processors, videocards, ram etc. can be heated up to very high temperatures, even in normal use.

Fortunately, these days, most hardware manufacturers make special equipment used in the incident of overheating of the system damage. This may stop what you do with your PC or you lose your data you're working, when stopped by these security devices. You could use a software that could help overheating CPUand will allow you to save your work and your PC is never a point on the need to provide protection against high temperatures.

Many of the options available third-party tool to be able to help you find the equipment you need to really continue to monitor. This would allow the PC to work, even too much for this! If you currently creating a better cooling hardware or if you use a system that a lower temperature must take allperiod of CPU usage, you can monitor the impact on the CPU cooling system. This is indeed a useful tool to make your PC work on its better performance and lower the temperature. Many sellers of these third-party software tools are available at a very affordable price.

With the third party to monitor CPU temperature software installed on your PC or laptop, you can ensure that you know when it's time to close it, or do forms ofuse that cool the CPU. This may be caused by a large list of different components, but the use of warnings and options available to prevent errors in your system, you can ensure that your laptop or PC long enough to when it's time for a new laptop or unfinished.

Thanks To : Linux Server Handbook Store Save! Can Liners Virtual Vine

Wednesday, December 1, 2010

Gigabyte P35-DQ6 motherboard

The GA-P35-DQ6 is the next generation of high performance motherboards from Gigabyte. Based on the killer combination of the new Intel P35 chipset and support the latest multi-core processors up to FSB 1333MHz, including the upcoming 45 nm platform. In addition to setting new records for outstanding performance, the GA-P35-DQ6 features an all-new copper Silent Pipe thermal solution for both the chipset and CPU power MOSFET, dramatically reducing the temperature around the CPU. The GA-P35-DQ6is also part of the GIGABYTE Ultra Durable 2 series motherboards with high quality electronic components which provide optimized power savings, ultra cooling and extended system durability. For more information on the Gigabyte P35-DQ6, copy the link below into your web browser: www.tigerdirect.com

Thanks To : Wireless Fence Harddisk Store Buy Cheap TurboTax | LOWER Prices

Tuesday, November 30, 2010

Build Your Own Computer: Picking a CPU is the first step

The most important step, because the first take in building your computer, selecting a CPU. Almost all the authorities in the field will tell you so, and for good reason. The whole system design is based on this selection.

The CPU power defines the type of motherboard gives you an idea of the power requirements for your computer, and, of course, the speed with which it is capable of. Different CPUs, can be effectively used indifferent units. One that would be ideal for surfing the Internet and word processing may be insufficient for use in a computer game. In the reverse situation, a way of CPU player would have exceeded the needs of a person who wants to build a basic PC. It would be like buying a Ferrari if you needed was a pretty efficient Toyota.

When deciding on a CPU, I suggest you ask yourself the following questions.

First, how fast your computer to go? Previousexample of a standard PC chip that can be achieved by going at very cheap prices that are obviously nowhere near the top of the speed scale. My advice is not much cheaper, slower and very smart out there, unless the price is the main concern. Get something a notch or two faster, if your needs grow later.

Secondly, how much you can afford to spend? The latest CPU sell for hundreds of dollars, but the chips are almost as quick to sell for only a fraction ofthat amount. It has everything to do with the industry is strong competition for new and better products on the market. What was in possession of a jewel in the crown a month ago, is now an element of discount. There are great deals around.

Thirdly, the chips have a reputation for running hot? This should not cause the reverse, especially for heavy tasks such as games, 3-D animation, and the like. But it will influence the design of the computer, accompany you to a water-cooledsystem.

Recommend : Previsioni Tempo

Monday, November 29, 2010

Vapor-X SAPPHIRE Radeon HD 4870 1GB 256-bit GDDR5 PCI Express 2.0 x16 Video Card

I made this card for a couple of weeks and could not be happier. This is the first offering high-end, I bought one of the two largest graphics companies, and it happens to be cheap.

In addition to great value, are generally satisfied with the extreme performance of this card. E 'treatment of all that I could throw at it including the kitchen sink and everything else from the North Pole to South Pole

While the fan is very quiet,is very quiet. And if it is strong, very strong. I noticed that little or no audible up to 30 percent, very quiet at 40 percent.

By the time you hit 60 percent the speed of the fan, it tends to be in the upper range of what most people would consider acceptable. If you hit 70 to 80 percent is extremely difficult.

But I tend to leave the fan on auto and rarely reaches high levels when you play a game. Only when in trouble with the fan speed manualconfiguration.

But if you plan to observe more and produce more heat would not be surprised if the fan noise is very acceptable.

Although it tends to be slower than a 4890, I feel the 4870 is about the 'sweet spot' in the segment bang for your buck. We would all do well to spend more money to keep the 4890 and slide to the side in 4870 to buy a secondary Crossfire mode on the road.

When we start playing with these aretype of computer performance an extra 4870 would be great. For now, the 4870 offers exceptional performance in a very good bang for your relationship to the dollar.

Friends Link : Spark Energy Vehicles Hybrid

Sunday, November 28, 2010

Software & PC Maintenance Tips

PC Most owners think their computers are disposable. If the system fails, it is replaced by a newer (more expensive) model. There are many programs you can use for your system in tune, but we must first discuss some basic things you can do to the life of your computer system to expand.

The worst heat of a computer! Heat can cause parts to wear out much faster ...

Basic Computer Maintenance:
The first thingyou should check if your computer has adequate ventilation. Check to see if there is anything that can block the air and out of the system. The space around your system will run cooler. Some offices have a computer cabinet in place in your computer, if you have a desk like that, that's what you can do to help ventilation. In the back of the box, cut around the holes where the PSU (power supply) fan is positioned so that the boy will be ableoutside the cabinet, also cut holes where at least fans can be positioned so that they can vent outside the case even in the room. In some cases, simply cutting a big hole in the back of the cabinet, will help with ventilation. If a door, leave the door open while the computer's operating system so that the system can draw cool fresh air into the case. If the door is closed, the air alone can bring the computer where the heated air is released fromcase.

Monitor Maintenance:
Second, make sure that the monitor is equipped with space around it so it can heat released outside of the case. Never block took a monitor, LCD monitors also release a lot of heat. Keep breathing!

Maintenance Computer Case
The third thing you can do to your computer is intended to extend inside the computer case clean.
The dust, the worst computer afterthing. The powder acts as a cover for the components. Keeps components releasing heat, which can lead to overheating of the components. Even a light layer of dust on your components can cause up to 5% more heat, as in the system. Before the next step, make sure that this does not invalidate the warranty. Make sure your computer is off first. Open the computer case or a screwdriver, or simply turning the screws to open (some systems). Make sure that the soil Before touching any internal parts. Your body can carry static electricity, and can be removed by touching all the parts that could damage the components. Do you have something in your business to the next section do not touch. Start vacuum all the dust you can from your business, take care not to damage while doing so. Subsequently, the compressed air can buy from Wal-Mart, or an electronics store, and bladder all crevaces, CPU> Heat sinks and fan / s, component heat sinks and fans, including video cards, sound cards, etc.. Once done with that, blow the dust from your case as best you can. After you let the dust settle down, blow the case again. This can of air will help clean the keyboard and mouse too. Vacuum first, and then blow the rest. With regular cleaning, you can add years to life on your keyboard and mouse. WhileIf you have opened, the next step.

Hard Drive Maintenance:
First, his hard drive designed to work horizontally, not vertically! Using the hard drive vertically, can lead to premature bearing wear. With the vertical drive, not even the weight of the disc, and moving parts, as well as horizontal scrolling, there is an equal weight. Hard drives can quickly wear out if not properly installed. If your hard drive is mounted vertically, to see if they can bemounted in any other place where wiring will reach a good place in a CD / DVD Drive / s and a floppy disk, hard disk locations. Try moving the stations where they will be flat. May need to CD / DVD drive to move it to work. They sell some kits that the hard drive to fit in a 5 1 / 4 drive bay will fit.

If you have a case designed for a case fan / s, what! Usually cost about $ 10 and could add years to your lifecomputer. They will help your computer run much cooler.

Remember that your computer room for ventilation and keep it clean inside, and will be around for the next year ...

Using a good software for PC maintenance can help the system to work more and have less problems.

Thanks To : Intel Core i7 920 2.66GHz Store DiggReview The Site To Review Interesting Products Sony VAIO VGN-FW465J Store

Saturday, November 27, 2010

About LCD Monitor

Liquid Crystal Display (LCD) monitors were very expensive compared to conventional CRTs, and then were generally only used in laptops and similar devices. But in the recent past the prices of LCD monitors have declined significantly. Currently they are equally accessible to low-end users. LCD is still more expensive than other monitors in the market today. But consumers found many benefits in them. The first is energy efficiency, which convincesconsumers to opt for LCD, despite the higher price. The sleek and stylish monitor is much sought after because of the higher quality product dominates the other categories.

LCD monitors are available in various sizes from 17 to 26 inches. Whereas 17 to 19 "monitors that are widely used for routine purposes. Users who want to display in widescreen and the graphics in the game look larger, which are 19 inches and above.Apart from the size of the monitor, there are some other important factors to consider while choosing this monitor. Native resolution is very important. It represents the number of pixels horizontally and vertically on the screen. For example, the native resolution of 1920 x 1080 in a 23-inch monitor is considered sufficient. lower resolution will result in blurred images and disproportionate. But for a basic use of computers, the native resolution is notvery important because the low resolution has little effect on the functioning of the system. When it comes to movies, games or graphics display resolution will have a key role to increase screen space and provide sharp images.

contrast ratio, aspect ratio, response time and other factors in choosing the most relevant monitor. The relationship between the lightest and darkest colors on the screen is known as contrast ratio. Is the responsethe time to look through the photographs of the liquid crystal. Aspect ratio is the ratio between the horizontal and vertical length of the screen. Conventional screens have a ratio of 4:3, while the 16:9 or 16:10 widescreen will. It 'was then applied to high-definition screens. In addition to the above features the viewing angle is an important factor. A minimum angle of 160 degrees is needed to provide comfortable viewingespecially when some people look at the monitor together. The interface is another feature that should be considered when buying a LCD monitor. Most monitors have VGA analog connection via standard video cable to your PC. DVI digital interface for connection is essential. Modern LCD monitors are equipped with an HDMI connector interface standard for high-definition display.

LCD monitors have become very popular among consumers.This trend is reflected in the flow of products on the market. Some of the best quality monitors are sold in the United Kingdom by producers in the area such as Acer, HP, LG, NEC and Samsung. There are several other brands such as ViewSonic, Dell, Fujitsu, Sanyo and Toshiba also popular in global markets. Consumers can visit the relevant websites exclusively on this monitor, that the marks can provide information about the authentic products, as templates,functions are included, and comparison. Independent evaluations will be useful for consumers to evaluate products and make a choice, depending on your specific needs.

Friends Link : Network Attack Case, Information Gigabit Hub Spec

Friday, November 26, 2010

Gigabyte GTX 470 SOC

Gigabyte redesigned the PCB (printed circuit board) for the new SOC 470 GTX (GV-N470SO-13I) and discussed, the energy consumption of heat and noise that the other 470/480 's are known for. Good results have led ...... It uses less energy than a standard GTX 470, even if it's clock, not put up much heat and the 3 fans are super quiet, even when they are setting high RPM. (Fans who have heard the case fans ... 5 of them on high beam) Gigabyte Good job! (Sorry for the bad videoquality. Taken with my digital camera and has no autofocus was a bit 'dark) My PC Specifications: CPU ........................ . .... 3.16 GHz Intel E8500 4.12GHz CPU Cooler OC'da ............... Thermalright Ultima-90 Motherboard .............. ASUS P5Q Deluxe Memory ....................... Mushkin 8GB DDR2-1066 1095Mhz GPU OC'da ............ ................ SOC Gigabyte GTX 470 (845/1690/3900 OC'd further) Food ............ PC Power & Cooling 750W Hard Disk Blue ............... 2xCase Western Digital 640GB ........................... Antec Nine Hundred keyboard ............... ..... Logitech G11 ......................... Cooler Master 5600dpi Sentinel Advance OS ........... ..................... Windows 7 64-bit and Windows XP Pro Dual Boot

Related : Brass Tube Enter Sweepstakes Fabulous Super Store

Thursday, November 25, 2010

About übertakte ich meinen AMD Prozessor [HD]

Ich in diesem Video zeigen, mit der man AMD "AMD Overdrive Utility übertakten Kann. Hierfür sind Recommended Program: AMD Overdrive Utility (www.chip.de Core Temp (www.chip.de CPU-Z (www.chip . Standartkühler de Achtung NIE mit keinen oder gar mit Gehäuse a handful of Lüftern übertakten PS: Wenn der Mauszeiger gefällt Euch, auf ihn downloadet pcwizkidstechtalk.com Test: www.youtube.com

Visit : Wireless Headset Save Price! Store iPod Touch 3rd Generation Store Instrument Calibration

Wednesday, November 24, 2010

Building a Home Theater PC (for Cornell Solar Decathlon)

Cusd.cornell.edu *** *** This video shows the construction of a Home Theater PC. E 'was built by me and other members of the Cornell University Solar Decathlon Team Engineering Controls. The computer uses a Core 2 Duo 3.0 GHz, a 128GB solid state drive and an Nvidia GeForce 9300 GPU chipset embedded in her 730th. The media has served as a home server. This computer is built with the following design goals: EFFICIENT Power Usage:Performed using a low wattage CPU, a solid state disk drive, a power supply certified for 80 + and a motherboard with energy saving features. Extremely quiet: it uses a Solid State hard drive vibrations, two silent 120mm fans and an efficient structure to eliminate the event. HD Experience: Integrated GPU offers HDMI-HDCP video output is enabled at full HD resolution, while reducing heat and power consumption due to the lack of video card, Ethernet Gigibit allows streaming of contenthome home media server, 3 GHz CPU offers enough space for video decoding. This HTPC will be used in competition Cornell University Solar Decathlon in October 2009. Learn more about the team www.cusd.cornell.edu bill and the music (eBEAT) are available for free download on the project page: Music www.ultimatecomputers.net By Alex Miller: www.youtube.com

See Also : Blu-Ray Movies Store. LOWER Prices in Same Item Dedicated IP

Tuesday, November 23, 2010

Beam test link

Nexus Beam Test piccolo, which allows for simple conveyor UN optimize and direct the flow of air out of the fan from pc.Il pc used and installed the United Nations, the small case slim.Cpu with passive heatsink fan 120 and Applied Silla side wall with the task of cooling the CPU, RAM and chipset. Using the Beam NU gets net drop in temperature cpu.Oltre 5 degrees Celsius after 45 minutes the CPU temperature otrhos son stabilized at around 48-49 °and from there you do not always move or 15 Minutes. The only Installation of the conveyor can drop to 7-8 ° 42 Minutes! Awesome! Trae Safe Mind System Very beneficial use because Questo channeler and the fan on 120 mm equipment required UN 80-120 disturbs a little bit of air flow in the output. Test pupgna

Visit : JVC Television HTC Phone Store Can Liners

Monday, November 22, 2010

Evercool Buffalo Heatpipe CPU cooler unboxing, installation and REVIEW Part 2

I bought the Evercool Buffalo Heatpipe CPU Cooler (HPFI-10025) for my Intel Core 2 Quad Q9550. my temps were idle for installation 59C to 65C and 75C at full load 89c, after that my cooler temps went into stand-39C to 45C and 49C to 59C full load. I used Arctic Silver 5 Compound CPU.

Related : Blu-Ray Movies Store. LOWER Prices in Same Item

Sunday, November 21, 2010

Stop New Dell Laptop CPU (processor) to 100% jump from overheating during use and display of video

In October 2009 I bought a Dell Latitude E6400. As a tech I have done my duty to check the specifications (CPU, FSB, the speed of hard drives, etc. ..) and user reviews. I did not know that under the bonnet was a heating problem that cripples the system time to an hour. Imagine being close to completing a project and all programs are stopped. This is the problem I faced after the money for a brand new laptop.

I isolated the problem to use the video.All applications for video-intensive (flash video, DVD playback, SlingPlayer, etc. ..) my laptop would increase the CPU usage to 100% after about 20 minutes of viewing. The CPU usage would not fall until the computer had been sitting for an hour. I tried updating drivers, updating bios, and also making the switch from Vista to Windows 7. After I upgraded my computer to Windows 7 and still had the problem I'm sure all my money went to the bathroom, but in a last attempt I metmost utilities forum and read some more and determined the cause of the problem. The graphics chip (GPU), which was overheating my CPU clock down to 500MHz and 800MHz.

I have read forums about all the failed attempts to use to solve the problem causing the overheating of the CPU to 100%. Some replaced the heat sinks, replace some internal fans, some tried to wait for Dell to develop a BIOS update to correct the tables of heating. None of these fixedapplication. After a deep thought that came to my mind we have an overheating why not add an external fan. I went and took a simple fan of the laptop and has eliminated the problems of overheating. I have two 20 "monitors connected to my docking station port-E and solved my all my problems. Now, I love my laptop and it works fine.

Visit : Guard Shack

Saturday, November 20, 2010

LCD monitors with digital standards Extreme

Although the brain of a computer is the CPU, there is a fundamental component of this is sitting humbly, without any idea of what an important role. We are talking about monitoring, without which there can be no computers. In recent years, a series of technologically advanced monitors for export in view of the digital format. We have also seen many recent technologies that promote a gadget aspects of speed, control,memory, etc. The news we've seen in the case of picturisation monitor is clear, clean and clarity of presentation. And speaking of clarity, the LEDs and LCD monitors in the front line. LCD Monitors have applied for a lot 'of time and monitor LED are approaching. But LCDs have brought great changes that have a lot to achieve.

LCD a key role in the prevention and eye problems related to stress related to usersand so can be called "user-friendly." They are also eco-friendly because they emit very little heat. These monitors consume very little power compared to CRT monitors and are profitable as well. They have a large bandwidth and makes an excellent contrast of the text. There was also agreement in scale, so the screen can be displayed with a uniform brightness without partial shading in a portion of the screen. These monitors are lightweight and thereforecan be carried around easily. With sharp edges and smooth finish, LCDs are rarely affected by aging.

The best feature of these monitors is the "corner", which can be customized to the needs of users. They also have an inherent resolution fixing "stuck" pixels is developed and therefore there are no problems in terms of image quality. The maximum brightness of these monitors is limited by backlighting - this aspect is considered thebest feature of these monitors. They have different native resolutions are adaptable to any scale of measurement. Sporting multiple video inputs, this monitor looks very elegant.

In addition to televisions, LCD monitors are available for both desktop and laptop computers. Approval of the monitor can be adjusted according to the brightness setting the options, including brightness, contrast, sharpness and color, making themall conditions. difficult lighting conditions do not affect this beautiful display. Coming in various colors and designs, the maintenance of these monitors is very simple. Although the cost of repair is very high, this sturdy monitor rarely break, giving you peace of mind.

This LCD display to avoid the sedimentation of dust particles and other pollutants on their surface. Some LCD monitors today are facilitated with touch screentechnologies that help to access the information needed for the blink of an eye. anti-glare screens are also available these days that are useful in the prevention of light reflection and improves the quality of vision. Unlike other monitors, it will not be affected as a result of some form of environmental factors such as severe weather, external vibrations, wind, etc.

Related : Network Consulting Buy Cheap PS3 Games | LOWER Prices in Same Item

Friday, November 19, 2010

About computer processor or CPU

computer processors or CPUs were compared to the year 1960 and much has changed since then. With the advent of transistor technology and semiconductor processors are fast becoming smaller.

There are many features of a processor that affect its ability to quickly and efficiently and to implement a number of these will be discussed here. Key features include a computer bus, clock speed, cache, CPU socket and the cooling systemattached to the CPU.

The bus of the computer determines the speed of the CPU or processor can communicate with other components inside the PC, the faster it can do that can run faster and complete the required tasks. The bus speed can also depend on the connection processor socket Socket 7 for example, providing one of the bus speed.

The clock speed is the main feature of the processor, this is the speedthat the task is completed. The faster the clock speed, the faster the PC. Because it is not very efficient performance of a task and start another how hard the processor is called a parallelization technique is introduced to synchronize more than one processor in a PC and as such more than one task can be completed in time. This technique is called Hyper-Threading, Intel.

The CPU cache is an important feature of any modern CPU, allows a quick recoveryfiles from the processor and as such help to increase the performance of your processor.

As I mentioned briefly the outlet is an important part of the performance of the CPU, there are many outlets are available and depending on the manufacturer depends on which bus you can buy. Since each processor uses a socket connection specific, only a small number of motherboards that will be compatible with that model and, as such, when purchasing a CPU,motherboard should also be considered good.

In addition to the internal functions of the CPU of an external factor that affects performance is the CPU cooler. To the best processors to be cooled when the parties in very hot. To do this, a heat sync to be mounted on the CPU heat sink with fans needed.

Thanks To : Rosetta Stone Store LOWER Prices in The Same Item External Harddisk Store Canon 500D DSLR Camera Store Best Price

Thursday, November 18, 2010

Crysis Warhead Benchmark ATI 5770 + @ 4.2 GHz i7 920 PART 2

Crysis Warhead Benchmark. Part 2 of 4. The full specification of the system: CPU: Intel Core i7 920 C0 @ 4200MHz (21x200) 1.49V + Arctic Silver 5 (HT enabled) CPU Cooler: Noctua NH-U12P SE1366 + 800 ~ 2600rpm Silverstone 107.9 CFM GPU: Club3D ATI Radeon HD@5.770 standard clocks and standard cooling Motherboard: Asus P6T X58 RAM: Corsair XMS3 3x2GB DDR3 1203MHz 8-8-8-20 PSU: Corsair HX1000W HDD - 2x Western Digital 37GB 10000rpm raptors in RAID0 (OS) + 300GB 7200rpm Seagate (storage) DVD Drive: LG 20x GSA-H55LDVD Burners Hardcano 13 + fan controller 4 temperature sensors Case: Chieftec GH-01BW-OP 1x 120mm fan (rear), 2x 80mm fans (front) Keyboard Logitech G9 Mouse Logitech G15 Samsung T240 - 24 "1920x1200 5ms Contrast 20,000 dynamic: a driver ATI Catalyst 9.12 hotfix OS: Windows 7 Ultimate 64bit camera uses the video to 1280x720 (720p) recording: Sony DSC-W290 editing software: Sony Vegas Pro 8.0 software monitoring: CPU-Z Version 1.52 0.2 (CPUspecific) GPU-Z version 0.3.8 (GPU specifications, voltages and temperatures idle) Afterburner hardware monitor v1.4.0 MSI (load temperature of the GPU fan speed and GPU) ATI Catalyst Control Center (demonstrating that the speed of the GPU fan is an automatic) real-time 3.00 (idle and load temperatures CPU) Windows Task Manager (CPU utilization) Introduction: www.youtube.com If you have any questions please do not hesitate to ask!

Visit : Memory Module External Harddisk Store. LOWER Prices

Wednesday, November 17, 2010

Diagnosis and troubleshooting Hardware

What is the hardware?

Do these terms sound familiar? Monitor, RAM, CD, CPU, graphics cards are all hardware, or more precisely, the computer hardware. These components are a computer, working with computer software on a computer to function.

In short, the hardware is the tangible part of your computer parts you can touch, feel, and so on.

Hardware Issues

As mentioned above, for hardware and software work together to complete afunctional system, in theory. However, we rarely get a fully working system at all times. There are almost certainly the fault of hardware, both in electronic circuits or even the whole component. Sometimes the input source is not the fault of the hardware components of the system itself but by external factors such as environmental disasters such as fires, earthquakes and storms.

Restoration of defective hardware is not a greatproblem in itself. In reality, is to identify and replace the problematic component. However, hardware faults are more deadly when they affect the daily habits that affect critical personal or business data. This is particularly true for the main component of a computer system for data storage, the hard disk.

The following is a list of common hardware problems:

Defects RAM
Power Connector
Hard Disk
Overheating
LCD Defects
Motherboard
USBBox

Defects RAM

Bad RAM is somewhat difficult to diagnose because similar symptoms can be caused by software problems, hardware problems or other defective motherboard. But if you have any of these symptoms, users must check bad RAM before all the other problems.

Symptoms:

Windows does not start with a different error message every time.
Windows crashes (blue screen) or locks up often.
Windows crashes when you try to start a program.
Unexplained random crashes and freezes without error.

Power Adapter

The common defect in a laptop is the DC power jack. If someone trips over the cable and adapter is still connected to the laptop, there is a high possibility that the power jack will be severely damaged.

In most laptops, the DC power jack directly soldered to the motherboard and there are only three or four small pins stuck, making the power jack rather weak.Each side to draw the DC power cord while the laptop used to release at least one of these pins, breaking the solder around it. modern laptops use a lot of power, about 70W to 120W or more. The poor electrical connection pin displaced sparks and heat that will eventually burn a hole through the motherboard and can even cause a fire.

Symptoms that the contact between the DC power jack, and indicates theMotherboard:


The battery is not charging properly or remain in the middle of the structure, despite the fact that the adapter.
The flickering of the screen (brightness variations), while the cable is plugged in. This is caused by the transition between the laptop DC power (the screen is brighter) and battery (screen is dimmer).
The hot-plug DC after a few minutes of use, and may also smell something burning.
There are "scratching" sounds from the DC jack.

As proof of the power brokenjack:

1. Remove the battery

2. Connect the power

3. Start the laptop

4. Gently rock the DC plug on the back of the laptop

If the laptop suddenly shuts down (losing power), find a dealer to re-weld or modify the DC power jack, not just the mother has already started to burn around the pins driven. The manufacturer may offer to replace the entire motherboard, but the price of a new motherboard with the cost of laborinstallation will generally take more than the present value of the laptop and the cost can sometimes cost more than a thousand dollars.

Replace or re-solder the DC power jack is not an easy job. It usually takes several hours, depending on the damage and the model of the laptop. Reaching the power jack, the handset must be completely dismantled and removed the motherboard. Then, if the card around the pin is driven badly burned, the power supply must be welded and un-the board must be patched.

After another power connection must be installed, affixed to the body of the laptop and connected by cables to the motherboard, because the Council would not be strong enough to patch the original type of power connector soldered directly to support the Board of Directors.

Hard Disk

hard disk failures are the most common computer hardware. And laptop hard drive desktop hard drive more often because of the portability of a laptop comparedsluggish laptop. If you blow or a fall of the laptop, even a few centimeters, while the hard drive is accessible or activated, the damage can be done for the HDD.

Symptoms:


The laptop starts up as usual, but when Windows starts to load it in bluescreen with "UNMOUNTABLE_BOOT_VOLUME", "hal.dll missing or corrupt" or "WINDOWSSYSTEM32CONFIGSYSTEM" (or similar) is missing or damaged. All these error messages indicate a problem file. Sometimesdetermined by a simple scan of your hard disk for errors. But more than half of these cases show that the hard drive starts to go wrong and probably is the development of bad sectors.
The laptop starts normally, but Windows crashes on the first "Windows XP" screen, but the blue bar keeps moving, and users are able to listen to fake, but constantly clicking. The hard disk must be replaced.
Once the laptop is started, there are loud clicking or grinding noises, and Windows will not load. HardThe disc must be replaced.
Shortly after starting the laptop a message (usually on a black screen) "SMART test failed. Backup your data immediately and replace the hard drive" or something similar. Well, this says it all. SMART is a self-test that is created on the hard disk.

In almost all cases, the laptop can be booted from a CD "live" bootable and everything works normally. In rare cases, the disc drive PCB (Printed Circuit Board) may have shorted out and even burn. Inthis scenario, the laptop will not start unless the hard disk is removed.

A good tool to use to check the hard disk life is the pawn of ADRC. It scans your hard drive for bad sectors and will inform you if the drive is good usability.

Overheating

Overheating occurs when the air flow enough outside the computer case and motherboard and CPU on the back of the case usually via the power supply fan and other case fans.

Once the airflowdistortion, the heat builds up quickly in the case. This ensures that both components of close, if such protection is not built or is working properly. In the long term, it can cause irreparable damage to the components to overheat.

You should also keep your computer in a dry and shady is substance and not clean.

LCD Defects

The most common LCD or liquid crystal display is faulty inverter, cable and lighting.

Symptoms:


The handsetseems to start as usual, but the screen is black, as users move, and seems to work well. Unable to cable.
The laptop appears to start as usual, but the screen is very dark, but it changes the color a bit 'and users can view an image look fake. Failed inverter or cable 90% / 10%.
Immediately after the start of the screen is dark pink / dark red and turns after a few seconds. backlight failed.
The screen flicker a few times, but dark, if users move or touch gentlythe sides, flickering again. Unable to cable or LCD 50% / 50%.
The screen is black or white (no picture) and the external monitor works. Unable to cable or LCD 30% / 70%.
There are stripes on the screen (horizontal or vertical) that change as users move the screen or touching the sides. Unable to cable or LCD 10% / 90%.

Motherboard

The vast majority of failures are related to the motherboard due to "Ship regulated component failure within those circuits. L 'board power supply circuit had partially failed and was overloaded following parts otherwise the problem would be the capacitors are damaged first.

A motherboard on a laptop that is out of warranty would usually means it's time for a new laptop. The price of a new motherboard is usually higher than the present value of the laptop.

Symptoms:

Connect the power adapter and try starting the laptop.


Nothing happens.
"ON" lightrises, the fan is running, but nothing on the screen (black) and you can not hear the HD working after 10-15 seconds.
"ON" lights up, the fan runs, but after a few seconds the light goes out.
After pressing the ON button, the screen stays black and you hear a sharp noise from the handset.

damaged or incorrect driver and the operating system

device drivers, invalid or corrupted can wreck havoc on a server, making the system unbootable in some cases.Device drivers may also conflict with certain applications and problems with the computer system.

If Windows Vista has just launched, it is likely that some hardware is not supported or not fully support the new OS.

Even system updates, driver updates can also fix your "hardware" problems.

See updates and fixes

It also helps (occasionally) to call their support service to assist the driver to the specifichardware.

Controller will not:

A controller can not act much like a disk failure. However, if a drive fails, users can not access that particular disc, if a controller fails, users can not access all the records, equipment and all other components connected to that particular controller.

A controller fails because a component or components on the controller board failure. When a user tries to boot, can not afford it, view, access, or evenget messages hardware conflict.

Controller failure occurs because of one of the following reasons:


Equipment / components are not connected
Make sure the cables are connecting the device / component to the controller
If the item fits into a slot, which is not rinsed, and loosely connected.

Equipment / parts are not set
Check that the equipment / components correctly identified and set in the setup of the controller onscreen

Bad connectors
Replace the bad connectors with new works

Poor shares
Replace the part

Poor interface card or motherboard
It is recommended that these parts are replaced or sent for computer maintenance


Hardware failure: the big problem

The big problem, as discussed above, not replacing or repairing non-functional hardware, but the lost time, breaks the daily routine (especially forcompanies), and the loss of important data. If you have a working system at any time, have a backup system as a fail-safe, or even two. If users want to make sure that none of their critical data lost in the event of a hardware problem with their computer, there's only one way to do it - back up your data as often as possible.

There are many ways to ensure that the data backup, and as technology advances, one of the methods of backup much easier.

Let's seeAs a backup. Back up the files on your computer means that users copy the data somewhere else and then saved to the computer network. Everyone should always have a backup of important files, at least, because you have a hardware problem, it may still be able to open the files.

Many people do not back up their files because they do not know what to do a backup. Start with those files that can not be easily recreated. Then,move on to files to which you make frequent changes just in case you accidentally change something that you shouldn't have. Back up your music collection - because this can be quite expensive to replace in the event of data loss.

In general, best practice is to back up the files at least monthly and more frequently if users access the files regularly.

Recommend : Plasma TV Store. LOWER Prices in The Same Item Pocket PC Pda Iridium Satellite

Tuesday, November 16, 2010

Choosing the right hard drive for video applications

With the P2, SxS solid-state acquisition and other media, nonlinear editing, and the need for rapid access to archived content, his records have become indispensable tools in video. There are many choices out there, but how do you find the hard drive on the right for your organization? Here are some things to consider:

Consumer vs. Professional Degree

As it is, with disk and tape media, there is a big difference between a professional quality and consumer-grade hardunits. Consumer hard drives are designed for storing documents and family photos. Professional Hard Drive, as worn by polyline, made for professional video and audio content, which means:

More metal (and less plastic) parts - this makes the drive more durable and can hold up to the tough demands of professional content creation
transfer rate higher - this leads to a smaller number of frames
Heat sinks and / or fans to cool the unit - isnot so much the heat, the danger of the rapid heating and cooling the engine (a real danger if you hot swap disks). adequate cooling for the machine is not shocking encounter changes in temperature that causes stress on the disc.
Extended warranty - professional-quality discs are designed to last longer, and that manufacturers are back, providing greater safeguards for the parties and consumes huge amounts of video labor.CapacityHD hard disk space. Select a stationwhich is twice as much space you think you need. Ti is too large for faster than you think. I also believe that, like the size of the disk, the cost per gigabyte decreases. Yes, by purchasing a larger hard drive, you save money.

Interfaces

Select a drive with multiple interfaces, this gives you maximum compatibility between different systems. In terms of speed, the slower USB 2.0 and eSATA transfer speed, the fastest. When it comes to large amounts of dataflows, such as HD video, the faster transfer rate means less time to do the same video and less dropped frames.

Recommend : Linux Thread Audio Integrated Amplifier Buy Cheap PS3 Games | LOWER Prices in Same Item

Monday, November 15, 2010

The purchase of a desktop PC is not as difficult as you might think

The purchase of computers can be a prospect of confusion for many people, some elderly and teenage children ask their daughters to express their views or drag insistent sales assistant in the computer store. At the other end of the scale there are people who know exactly what they want and be able to rattle off a list of specifications that must have their PC.

When buying a desktop PC you'll want to make sure you get the best deal and do not buy something thatwill be given as soon as you bring home. Knowing a few key details can help you navigate the murky waters of the PC and make sure you buy something within your budget and suits your needs today.

First, a desktop can be big or small, it often depends on how you use your desktop as you want to play the latest games, the PC will be more significant because of the extra components and larger high-performance kit, which will be an insider .Computers will be used primarily for surfing the Internet and word processing are generally smaller because they are smaller, so does not generate much heat will be quieter and consume less energy to operate.

Many potential buyers of PCs will fall into the latter category and the advantage is that a general purpose computer is usually quite cheap to buy, this may go up if you add extras such as computer monitors or external storage such as USBhard drives, but overall a desktop PC for this use will be a relatively unobtrusive machine that can be stored in a closet or under your desk to be.

There are also computers like the iMac, which looks like a computer monitor, but in fact behind the screen all the other components of the computer are hidden, so that all computers can be on your desk with a single line behind the taken as most wireless keyboard and mouse too. These computers may look more likea fashion item from a computer that has seen a lot of people buy them for their home or are in the room or downstairs in the living room.

Make sure you have a budget in mind when buying a PC and get advice on what details you will probably need what you intend to use the PC.

Thanks To : Intel Xeon CPU Best Price Store Scope Covers Comet Electrical

Sunday, November 14, 2010

Green Personal Computer - How to Build a Green PC

Energy is something we are increasingly concerned with the modern world. Personal computers should not be ignored in terms of amount of energy they consume each day. A typical modern PC can consume about 100W in idle and close to 150W under heavy use. For a system of high-power game these figures can be doubled.

If the PC is left on all day, these figures represent a significant portion of electricity bills, especially if you have an officefull PC.

When building your own PC (s) may be taken to the machine as efficiently as possible. It should also be noted that to make your PC green but you have to take into account the amount of lead in computer components. Lead in solders for electronic components that make up a printed circuit board. Components that low levels of lead and other toxic elements are often branded as "RoHS" requirements.

There are three important contributions toenergy consumption of a PC.

1. Power Supply Unit (PSU)

The ideal diet should be 100% efficient, ie, the power consumed is equal to the power delivery from the computer. This is of course impossible, and what the force is converted into heat and sound, but modern PSU often greater than 80% efficient.

The power supply should also be able to provide energy when needed and not just sit on your PC to burn electricity when the power is not needed.

To be sure to choosea wider range of 80% efficiency, make sure that there is "80 Plus" certification. This also ensures that the ballast is lead free and RoHS.

2. Processor (CPU)

There are a number of available processors that are designated as "green." They tend to be a bit 'more expensive than their non-green, and even slower, but the performance difference is not huge. If you do not want to buy green for the dual-core CPU and check the stickspecifications for energy, especially when idling.

Of course you do not need a standard processor in your PC. You can in fact use a laptop processor, although you can hunt around for a supplier. These are low-power CPU and have a number of energy-saving features, but as a CPU are a little green 'expensive.

3. Monitor

If you have a good old CRT monitor, but you plan to use the new green buildingPC, think again. These types of monitors are hungry monsters that have now had their day. Modern LCD panels are greener, more energy efficient, and indeed a better viewing experience to choose the right type of panel.

Visit : Small Network Linux Thread

Saturday, November 13, 2010

Xbox 360 cooling in the computer case and heat sink mod

This is my xbox 360 mod, I have the 360 in a computer store and then put six fans in the case of an external power source. I drew some heat sink apart and folded into a square and wraped in duct tape that I put this on the chips were still warm, including those on the back. Alo I added a heat sink and fan for the GPU is also advertising on the CPU.

Related : Roofs Metal Reverse Text

Friday, November 12, 2010

How to make a / Laptop Buy

Want to buy a laptop you do? And look at the wide choice available, you are confused ..... worry .... Here's some advice.

Before going into details, a brief summary of processors is essential. Be aware that the processor (CPU), which governs the price of the handset (with the screen size). The two main companies are Intel and AMD (there is also Apple, but lets stick to the mainstream laptop). Intel makes the popular Pentium line of processors(''Intel inside''Ting Ting Tong Tong!). For laptops, there are three main CPU available - Mobile Pentium 4 (actually a desktop P4 processor), Pentium M (low-voltage CPU the battery life and increase built specifically for laptops) and the Mobile Celeron processor (P4 cpu poor). Wait a minute, you say, did not mention the Centrino processor. This is because it is not a Centrino processor - technology. Centrino is a combination of three things - Pentium M 855 CPU +Chipset + Wireless Pro (802.11b). The other company is - AMD CPUs are really good position to compete with Intel. Traditionally, AMD CPUs have heat problems, but lately there are not many complaints. I recommend you stick to the Intel processors that have a good resale value.

The next Q is .... what laptop? Are you going to use for simple things - spreadsheets / word processing / surfing the web? Going to a Celeron CPU. If youintention to make the calculation more serious, travel planning and often want the laptop on battery power, go for a laptop Pentium M. If you go for wireless access to a laptop or a Pentium M Centrino laptop (you can use a wireless PCMCIA card to be added). If you do not plan to move the laptop too much or you have a laptop for games, have a Mobile P4 laptop. But be aware that a Mobile P4 laptop is a desktop replacement - it will be heavy and hot.

Now that you havethe CPU has decided to consider the size of the screen. 15''is spot''vandaag''sweet. But you get smaller screens or larger. Choose the size that fits your budget. 14''of less is a bit 'too little these days, unless you want an ultra-portable (read expensive) laptop. For players, the larger screen the most fun they have. Larger screens are also good for warriors spreadsheets and desktop publishing.

The next item on the list is RAM (temporary memory). Most laptopssupplied with Windows XP at least 256 MB of RAM to run needs to be happy. I urge you to upgrade to 512 ram for best results. The more RAM you have, the better your notebook will perform. It is said that by increasing the RAM is the cheapest and best, the performance of each computer (ie without changing the motherboard / CPU).

Another thing to look at the graphics memory. You can opt for dedicated or shared memory architecture. dedicated memory means that yourvideo card has its own memory and not bedelen''''voor the memory of system memory (RAM). A rule of thumb - dedicated memory = faster performance. The players and the boys must insist on the DTP dedicated memory. Good graphics chip is ATI Mobility Radeon or Nvidia GeForce. The more video memory you have, the better. Try to have a laptop with 32 MB of video memory. Most laptops use the platform these days is a measure of cost savings (an architectural sharingIntel Extreme Graphics). If you're not going to serious 3D games or graphics intensive programs to run, the shared architecture, fine. But make sure you have enough RAM (see 512), because memory is a part of your RAM to steal.

The hard disk capacity of 30 GB will be in the region and beyond. Get the most bang for the buck - not that many de''Ik capaciteit''bronst will never be necessary. You already have space on your hard disk in order to obtainget the largest capacity you can afford. For laptop users normal 40 GB is enough. You can easily increase the disk space to buy an external USB 2.0 hard drive.

Battery life is very important for road warriors. Expect 3-5 hours of battery life for most laptops. Mobile P4 laptop batteries last much less. Always go for a lithium ion battery against a nickel-hydride batteries.

Most laptops provide optical drives - the best value for money today is the DVD-ROM + CD-RW. Thismeans that you can read DVDs and read / write CD. If you have a lot of money to spend, have a laptop with a rewritable DVDs have.

The sound quality on laptops is just acceptable for movies / music / games - you can not go wrong with Harmon Kardon / Altec Lansing speakers.

An important factor to consider is the weight. If you do not want a dislocated shoulder doing? So .... the lighter the laptop, the better for your health! The problem is that the lighter the laptop, the more expensive it iswill be. Do not forget the AC adapter - Some laptops are great adapters that weighs a ton!

Do not consider a floppy drive - most laptops without floppy drives anymore. But do not worry - external USB floppy drives are cheap. Ask the seller to give you a free, he will require if it is to make the sale. While watching, request a free laptop bag as well.

Get a laptop with lots of USB ports, which will be useful and to improve the versatility of yourPortable. Make sure that the USB ports are USB 2 (a technology that is much faster than the old USB 1.0). An external USB mouse is a must if the built-in pointing devices are really painful to use.

All notebooks come with built-in modem and usually have LAN connectivity. Some laptops have card slots that can read / write to memory cards (as used in cameras).

Most companies offer laptop minimum software - Windows XP and basic things. Will not even give your Office software. Willmore software to add yourself. lower prices, some companies offer Linux OS - unless you're seriously short of money, then you should follow the windows. Once the new laptop, make copies of CD recovery and safe storage of CDs. copies to bring with you travel a lot.

Now, armed with knowledge of the dip above the market and choosing the best laptop you can afford. Compaq and Toshiba laptops make excellent,check them out first. Compaq is usually cheaper Toshiba. I used a Compaq laptop at first, but later moved to Toshiba, as I found their laptops better. This is a personal choice not to read too much. Compaq and Toshiba are well established in most countries, so that repairs are no problem. Find out where the nearest repair and maintain the information at hand.

A laptop is usually a long-term buy - forget about upgrading laptops. So choose carefully. Check the warranty- National and International. Remember that some companies would not honor the international warranty and will tell you to take the laptop back to the country where you bought it! Be sure to clarify this point before buying the laptop.

Take care of your laptop. Invest in a surge protector. Do not move the laptop when it is running. And remember the golden rule - never drink tea or coffee while working on a laptop!

Recommend : Online Fax Service

Thursday, November 11, 2010

Soon Core i7 and X58 motherboards come Platform

The buzz is contagious. Anyone interested in technology, discuss the release of Intel Core i7 (Nehalem) processors, which should begin in November 2008. One of the main reasons why everyone is excited about this launch is because the Intel Core i7 is radically different from previous generations of CPUs.

The first obvious difference is that the Intel Core i7 motherboard that supports QuickPath required. QuickPath is a technology that providesAllocation of high-speed connections are a shared memory. This means that you can expect excellent memory. The Intel X58 and X58 motherboards support both QuickPath MSI.

The second difference is that the memory controller into the processor, not a separate chip. This means that the memory is connected directly to the CPU for better performance.

Many technology enthusiasts eager to experience the benefits of 4-core promise. Each of the4 cores can process two threads simultaneously. The operating system, the CPU seems so August 1 processors.

The Core i7 only supports DDR3 RAM. Looking synchronized with the launch date of Intel Core i7 has a memory manufacturers such as G. Ability Taiwan issued 3GB memory kit compatible and 6GB DDR3 triple channel. These memory kits are perfectly matched to the Intel Core i7 and X58 chipset motherboard game. At the time of writing, pricing and availabilityDetails to be announced.

But fans should not wait too long like the Intel Core i7 is already scheduled to be launched in November. X58 motherboards are available now, and everyone is just waiting waiting for the launch of next-generation processor.

When you combine the three components, the motherboard with X58 chipset, the Intel Core i7 and triple channel DDR3 memory, you get a very powerful machine, with impressive calculationpower.

Each component provides a range of possible uses that can be adjusted and optimized. For this reason, overclockers, gamers and those who can not resist holding this advanced hardware. Machines equipped with these components can be modified for optimal performance and testing of engine operation. This is very fun, exciting and fun.

Overclocking a computer can be risky, as incorrect settings mayhardware damage. This is largely because the standard cooling solutions are not yet fully developed to overclock with the elimination of additional heat. Overclockers often be forced to add on top of the cooling system to handle the extra heat.

However, the high-end hardware that we have just discussed, improved cooling technology has improved so that less cooling.

All in all, Core i7The X58 motherboard and DDR3 memory kits expects one of the most potent combinations in the world of computers.

Friends Link : Best Price Super Store

Wednesday, November 10, 2010

Monitor CPU temperature in order to avoid a collapse

Computer overheated is something that can harm your computer and devices, even though most new computers (both hardware and software) to protect it from happening, it is still a common occurrence. Mainly due to the increase in graphics cards for games fueled intense or watching movies online, the speed of the faster CPU in general and also something called overclocking. There are several signs to look out to see if the CPU temperature rises too high, some of themmay not even realize that this is the cause.

Things to look out for are the following:
* The computer restarts unexpectedly.
* In the middle of a game and it seems that every frame is moving slower than the previous year.
* The computer crashes too often.
* Computer suddenly isolated.
* Things are starting to run very slowly, were fast before.
* You must listen to the sounds of the fans do. They sound as if they were constantly running, or whether the soundsporadic, difficult moments, and then sound like do not work.

In general, the CPU temperature starts to rise when the computer is continuously operated. The heat starts to build and eventually lead to overheating. If you live in a warm climate and do not have adequate cooling in your area, can also accelerate the production of heat from the computer.

As you can imagine, a high CPU temps, resulting in overheating, which in turn can lead tohardware failures, and worse still, a fried motherboard, even though most computers today have a built-in security (system reboot).

Most motherboards have now integrated in the BIOS setup a way to temperature and CPU. When you start your computer, you must enter the BIOS and the health of the PC or power to go. You should be able to see what the temps for the CPU and the system. If you do not want to do this every time to check, youalso install the software on your Windows system, the CPU temperature will oversee all time. However, you must make sure your motherboard allows.

Normal CPU temps on Intel processors are typically waiting: 40-55 Load: 55 to 85, they tend to run higher and hotter than AMD, which in standby: 30-45 Load: 50-70.

If your CPU temperature seems to work very hot, you can take some steps to try to alleviatethis. A simple measure is one side of your tower open to the air flow inside it (but beware of dust can and will come). Another is to add or replace the heat sink on the processor with a better one. You should also make regular dusting off (with air or foot pump), the fans in both the computer and power. Finally, test the computer to maintain a cool job.

Thanks To : Inkjet Printer Ink iPod Touch 3rd Generation Store Fiber LIte

Monday, November 8, 2010

Common Problems Why Hard Disks Crash

There are many reasons why the hard drive has crashed:

(1) may be caused by mechanical or physical problems, such as the failure of the spindle motor system. This error is usually caused by overheating. Blink activity you see on your CPU (central processing unit) indicates that its head moves to different tracks. If this movement fails, can not read or write data. Remember, a hard drive is a piece of hardware, not software. This is amagnetic device for storing data, reads and writes data during execution.

(2) No system of logic (logical drives partitioned designated as C, D, E, F, G) can be caused by but not limited to the corrupted system files, corrupt firmware, registry hives and virus infection. Spyware, adware and other malicious files can also cause hard disk crash.

TIPS:

(1) If the activity flash, but the computer does not start, if applicable, your fileintact on the hard disk, but inaccessible - this may be the result of the failure of logical system. Try booting from a floppy or use the startup disk that came with your system.

(2) If there is a flash activity on the CPU and the system will not boot (obviously after having checked all the cables are "on"), then it is probably a mechanical problem. And note that if the system BIOS (Basic Input / Output System) can no longer recognize the hard drive,then the physical and mechanical properties of the system that has failed.

The good news is, usually, in today's technology on hard disks, if this problem occurs, it will normally be vigilant and on guard before the bombs, so it might be an opportunity to run immediately to get your file. And there are many data recovery tools available on the market today. But sometimes it is cheaper to replace the repair of the hard drive (unfortunately).

TIPS & TRICKS TO AVOID DISASTERHappen:

1. Keep your hard drive healthy by running Disk Defragmenter at least once a week (preferably every two weeks)

2. Run anti-virus program every day! Run spyware / adware removal tool at least once a week (there are many available for free download). Please also update all of these tools and programs! Turn off your firewall and pop-up blocker, protecting you from intruders!

3. Delete all unknown emails, clear your mass e-mail spamimmediately.

4. Delete all temporary Internet files (including all offline files)

5. Install all the necessary updates on your computer

6. Be very careful when downloading files from different sites (firmware usually fails because of this)

7. Last, but not on the list - taking back-up hard disk on a removable disk or tape as a serious task for you to do at least once every day or once a week, especially if you use it for commercial purposes!

Visit : Pocket PC Pda C Sharp Language DVD Store Save Price!

Sunday, November 7, 2010

19/10/2010 dirt2_game 00-06-15-36.avi

Callahan Kolín Mr.Razor / Czech Profesional Owerlocker / Hardware / Software Support "PC Name:" Black Pearl Asus PC Components: Speakers: Asus Black "air cooling system 3 mm Antivybracion 500Wat fabric material power Seasonic Blac Magic Power 2 Forton-X2 "300Wat" No Booster Acivated from Dual Graphics Processor Upgrade: Intel Pentium Dual Core 3.5 Ghz 2 x 2 x 2.6 @ Overlock Normal Normal Temperature: CPU / 42 cels.Cpu-1/42 cell. Cels CPU-2/42. Burn Mode: CPU-55 CESL. Cpu-1/57 Cels. Cpu-2/57 Cels.Graphics: GPU-NVIDIA 250GTS 512MB of DDR3 RAM, 256 Bit, 63 Gb / s "NO Owerlock" Support NVIDIA CUDA, Psych X, Nvidia 3D Vision Open CL, Direct Compute 4.0 "G92 GPU" CLOCK-675Mhz/Memory - 1008/Shader-1620 RAM: 2 x 2 GB Kingston 900Mhz Dual Chanel C, L-5.5.5.15 HDD: 160GB 7200 rpm 8MB Hitachi Satta2 Cha. Temp: Burn Idle/29Cels Mode/36 Cels. Audio: On Board HD Audio Azalia 7.1 Max Temp system in all mobile phones 57 to burn. Cooling: ASUS Q-Fan Control System CPU Artic Cooling System Rev. 2 "Heat Pipe 2 x 4" 120 mmAC Fan / 470Rpm standby / Burn Mode Max700Rpm Sot Bridge 40 mm Fan 500 rpm, the liquid North Bridge Fan 47 mm 500 rpm, the fluid frame 120 mm Xilence Heatpipe Cooling Fluid 1100rpm RAM Nexus HXR5500A DVD: LG DVD + RW / DVD-RW / DVD-RAM, 2 MB buffer operating system: Windows 7 Ultimate x64 bit motheboard 'Full On: Asus P5KPL-AM Idle/28Cels. Burn Mode / 36Cels. Chipset: Intel Bearlake G31 "ICH7" Bios: Bios Update all system year-2010-Max 14 dB noise! "This includes Max @ Max Silence" by 2010 Dezign "MrRazor Callahan...

Tags : PSP Consoles Store. LOWER Prices in The Same Item

Saturday, November 6, 2010

How to fix Vista Macro Mp712s 17 "CRT Monitor

The complaint for this macro mp712s 17-inch monitor has happened. Once the lid was removed and the power, he felt a soft chip-chip noise, the power to try to come, but something had to close. no LED indicator light. As another monitor problems troubleshooting, the first thing I do is look for any burnt mark, connecting cables loose, dry joints and burned components. True enough, there was a crystalclearly marked burned in the middle of the motherboard.

Close inspection showed that it was a FET with the part number IRF630 (n-channel FET) and is located in the S-correction circuit. Looking at the FET from behind the 3 main board that a joint clean cut. I think this is the reason for the FET burned. Usually when you connect a component that had found dry, it is very likely that you'll be dry joints in other areas. The scan found all along the linea large number of joints in a dry circuit and the most obvious was the area immediately after the secondary side power switching transformer.

Verification of the flyback internal capacitor, transistor output horizontal (HOT) and the surrounding components fet burned has not been possible to find bad parts, so that after replacing the FET power has been turned on. Now the monitor to boot, but without high voltage and I could smell something burning at the circuit B +area. monitor was rapidly switched off and unplugged from the AC plug. With my finger on the B + fet heatsink was very hot and it is not normal. Because of this, I suspect the B + fet have also developed a short circuit. Upon check in, so the B + fet was so bad. The part number is B + fet IRF634A and also with a new replacement monitor is still denied to the tension is high.

The only choice I have is to do a stress test or measuringwith power. Placing the black meter probe to the soil cool and the red test in B + pin of the flyback and power, there was tension on the pin. This indicates that the work of B + circuit and the error might be elsewhere. Since the flyback transformer primary winding and capacitor internal controls is fine, the only suspect in the horizontal driver circuit.

To use the oscilloscope to monitor this waveform at the base ofThe heat, I chose the option to measure the horizontal transformer driver. Placing the red probe to the supply line, as shown in the figure and the black probe on the ground with cool power, I noticed there was an unusual number registered with the meter reading. E 'was only about 4 to 5 volts (where it should have at least 12 volts) and pulse (the meter pointer moves up and down). This is the meaning we seek. From here we could take our time to concentrate on finding the realcauses.

Using analog meter set to Ohms X1 where the black probe on the supply line and the red probe to the ground cold, it should show a low reading ohms, but in this case the needle at the top (low ohm reading). Component should be short-circuited, causing a short circuit to the meter reading recorded. Tracing along the supply line to the horizontal driver transformer adjacent components found a shorted driver transistor Q401 to the horizontal part number 2N7000. Normallymonitor, engineers prefer to use a bipolar transistor as the transistor compares to the horizontal driver FET. A new FET closed to repair the macro view mp712s 17 "monitor.

Friends Link : 8 Port Hub XBOX 360 Hardware Store Save! Nitrus Oxide

Friday, November 5, 2010

Monitor CPU temperature

These are some great applications for monitoring the CPU temperature. SpeedFan: www.almico.com / speedfan.php Core Temp: www.alcpu.com/CoreTemp/

My Links : Intel Core i7 920 2.66GHz Store Harddisk Store Barcode Store. LOWER Prices in The Same Item

Thursday, November 4, 2010

The best mod for Xbox 360 fans can do!

This mod with my mod fan shroud (www.youtube.com) will greatly reduce the temperature of the Xbox 360 GPU and CPU and no more power than the old way of stealing from the cable DVD player! This works both ways are good for your Xbox 360 (1) It reduces the power required to power the fan at 100% of the fans running! This reduces the heat is on the motherboard and the power brick! (2) The fans are running faster to remove heat from the heat sinkskeeping all the Xbox 360 cooler. Note: stealing the power cable of the DVD to make sure that you and your Xbox 360 power brick needed to run hotter than offset by the add power to defeat the original intention of cooling the Xbox 360. Yes, you have to do with another plug, but the prolonged use of the Xbox is worth the added power! HO! More air means clean twice as often as the dust builds up faster! Last note: Do not overfeed the fans on Xbox 360!The EIA requires a little 'heat to work! We're not trying to connect the Xbox 360 the fridge! If the 12V power supply has too much power and have your fans you supercharged a variable resistor from Radio Shack for about $ 1 to add that not only delay and sour slowly. It would be a good idea if you run any of the new supply of LED lighting and power will allow you to have the lights on during the game, although I recommend a switch to the research...

My Links : Vulnerability Security Security Film

Wednesday, November 3, 2010

FSX HD

First video in HD CPU: (8-thread) Intel ® Core i7 CPU 920@3.80 GHz Motherboard: Asus P6T Deluxe Intel X58 chipset RAM: G. Skill DDR3 1333MHz NQ Series 12GB Video Card: ATI Radeon HD 4870 X2 2GB GDDR5 PCI-Express Dual DVI-I & TVO Specs: Case: Thermaltake Spedo Full Tower Case w / Window Side Panel Upgrade Power Supply: 1100 Watt Power Supplies (1100 Watts Power Supplies (Tagan TG1100-BZ 1100W modular power supply series of stone pipe)) CPU: (Quad-Core) Intel ® Core ™ i7 920@3.81GHz 8 MB cacheLGA1366 cooling fan: Cyberpower Advanced Watercooling Kit (including radiator, pump, tank, the CPU block, tubing and coolant) Motherboard: Asus P6T Deluxe Intel X58 chipset SLI / CrossFire Motherboard SAS DDR3/1600 Triple-Channel SATA RAID w eSATA Dual GbLAN, USB2.0, IEEE1394 & 7.1Audio memory (Req.DDR3 mother) (6x2GB) PC10666 DDR3/1333mhz Triple Channel Memory (G. SKILL NQ Series W / Heatsink Video Card: ATI Radeon HD 4870 X2 2GB GDDR5 PCI - Express Dual DVI-I & TVO

Related : Switch Hub Store. LOWER Prices in The Same Item Desktop Save Price! Store Vulnerability Security

Monday, November 1, 2010

Temperature monitoring CPU fan speed

It is believed that the best technique to extend the life of your CPU are monitoring CPU temperature. This act of maintenance, keeping the CPU and its internal components are running properly. Among the events of the CPU overheating, which are subject to a high risk of a collapse of the system. This will not only damage the CPU, but the entire system, including the motherboard and all the important information stored inthe hard drive too.

However, the temperature of the CPU, you must have a monitoring software and first make sure you have the capabilities of the motherboard ACPI CPU installed in the first recommendation would be the fan speed. This is certainly one of the best on the market. This is a freeware surprise that not only helps to monitor the CPU temperature, has the ability to hear the hard drivetemperature, voltage and fan speed, of course you can.

Now, as a tool to use as a fan to run the CPU temperature monitor certain that a basic hardware element. It will connect the temperature sensors in the area of the motherboard to determine the amount of heat accumulated in perhaps one of the best features of this fan is the ability to control the speed. If you have a group of fixed speed fans inCPU, you can know how each component or region, in the case is heating up. From there you can control the heat so it does not damage the CPU.

Another advantage of using the fan to the CPU temperature is the user interface. The information is displayed on the CPU heat is not only the temperature, it includes exactly the tensions in the system icon.If by chance that the measurements exceed a certain threshold, the software tells you the fan speed accident. Then, like an e-mail actions are taken to get the problem. With these advantages, the fan speed is definitely a sensible choice to monitor the internal heat of the CPU.

See Also : Remodeling Design Hole Drilling Awesome Price Netbook Store

Sunday, October 31, 2010

Raidmax Smilodon Mid Tower ATX case review

My video review of the Raidmax Smilodon Mid Tower ATX PC. It has green and does not come with a power supply. There are also Smilodon that comes with various feeds, you can get with blue LEDs, but the case is still exactly like that. I have not spoken in this review that the side Plexiglas also a place for a 80mm fan on the cpu area to install. I'm not a fan just to install, instead I built a plastic tunnel over the top of my Core2Duo CPULet the heat sink, sucking fresh air directly, as recommended on the Intel site. Overall I'm quite happy with this case, gets many compliments. There are three really nice green LED on the front line and the side fan is also a green LED fan. All fans are quiet. The side-opening door and coming off a great feature for easy cleaning of your computer every month or so to prevent overheating, very important for a system of play. My only twosticky issues in this matter is that although the door is nice, open when I connect the USB cable, headphone jack, using a microphone or DVD on the front, or on the computer. Just a minor annoyance at times. And secondly, I would like the hard disks have been painted black to match the case, would look better.

My Links : Buy Cheap Anti Virus 2010 | LOWER Prices XBOX 360 Hardware Store Save! Comet Electrical

Saturday, October 30, 2010

PS3 60GB Sharing with the voice and also in flames, with chicken (YLOD)

This is all my old parts of the PS3 until you guys what its like inside a PS3 now that you can subscribe to the rate and the remarks of the problem with the PS3 that im in the month to obtain a yellow light when I turn in this usually is caused by CPU or GPU to lose contact with the motherboard GPU in my case, has no contact with the motherboard as I do not it? I do not, because I looked down and saw through the pin, but no contact with the GPU, the CPU looks good so far .....How am I gona do? im gona buy a liquid solder flux is liquid flowing under the GPU and I'm gona use in a 420 degrés heatgun fareign height, so you can solder the GPU and all the dissolution fluid flow can be attached together by welding is actually the same league, so I'm gona warming, when the liquid alloy and in this way for about a minute until it starts to boil like crazy, then the CPU in this case are gona do both in the case, always the2 of them this may not last long, but it would take a couple of months and when it does repeat the process is not difficult to remove only do this if it's too late WARRANTIES AND NOT RESPONSIBLE FOR ANY DAMAGE TO PRESENT IM U!! !! thanks for watching subscribe rate and comment !!!!!=) PS3 PS3 PS3 heatsink fan heat sink on the motherboard (CPU Cell Broadband Engine GPU RSX) touchpad buttons PS3 PS3 (PSU) of the paper and PS3 wireless PS3 bluetooth...

Friends Link : Switch Hub Store. LOWER Prices in The Same Item Webcam Store. LOWER Prices in The Same Item Buy Cheap Bluetooth Headset | LOWER Prices

Friday, October 29, 2010

How to build your own computer

Build your computer from individual parts will begin with getting a motherboard, RAM, CPU and hard disk.

The motherboard is the part of every computer that connects the CPU is actually what makes your computer a computer, RAM is where you work on your computer does everything, and the hard disk where data is stored. You also need a video card, and will be a network interface card (or a wireless network adapter) will, and if you need a sound cardhas no sound onboard the motherboard. You also need a monitor, keyboard and mouse, and if you want a case for it and some fans. Suppose we have all the parts, and were smart enough to make a bundle to buy a place like NewEgg.com, where someone else has chosen the RAM CPU and motherboard, so all work together. (For computers that are "last generation" stuff, this is often a good way to get a really cheap computer for a small sum of money.)

OK,you go to a screwdriver, a need for good light and a magnifying glass does not hurt. Following the instructions for your case and motherboard, install the motherboard into the case. Connect the power supply wires to the motherboard, and attach all connections to the front plate and back plate. Power up - there are LEDs that light up, if not, you may need to talk to whoever sold you the motherboard.

Now, power down again. Set your CPUin the CPU socket, it can be difficult - but not forced. Everything should line up and you will get in. Now, practice the heatsink / fan on the motherboard, then remove it, apply some 'thermal grease on top of the CPU tries to put on a uniform and put on the heatsink. Usually there is a spring tension locking lever to keep using it. The main cause of death, forcing the CPU and motherboards in the first motherboardfolder and a pen, and tries to run without the cooling block.

Once the CPU, put the RAM in the slots, and connect the hard drives. Make sure when you buy the hard disks that use the same connectors on the motherboard (which is why we take the motherboard and work our way out). SATA hard drives are faster, bigger and easier to find than the old IDE. SATA vs IDE is a good reason to choose a hard disk onothers. Most hard drive bays are lives in media so you can mount the hard drives there. If your hard drives are equipped with fans, the fans are connected. Hard drives can be very hot, and it is not good for them.

Now, put the video card, the monitor, and switch - you should do a test "POST", identifying the CPU and how much RAM you have, and with luck, will tell you that found hard disk drives. Otherwise, you may need to lookthe motherboard manual again and play with some jumpers.

Finally, close all other parts where they should go, including the CD-ROM. You need the CD-ROM to install Windows or Ubuntu Linux. Leave the case open while installing the operating system, just in case something needs to be adjusted.

You're on your way to building your own computer.

Visit : Brass Tube